Getting precise, straight cuts on full sheets of pressed wood or MDF can be a costly recommendation. The ideal approach to do it is with a decent, hefty table saw. In case you’re restricted on space, you can likewise utilize a dive cut track saw like the Dewalt or Festool, yet those aren’t modest, all things considered. A less expensive choice is something like the Kreg Rip-Cut Circular Saw Guide; however, it is restricted to just 24″ cuts.
If you effectively own a roundabout saw, this easy to make zero-leeway roundabout saw guide would help you make exact tear and crosscuts in full 4′ x 8′ sheets of compressed wood. Since this roundabout saw cutting dance gets set facing the cut line, it makes it a lot quicker than other slicing guides that expect you to balance the guide some separation from the line. The plan additionally forestalls fragmenting and detach from the slightly compressed wood facade. Likewise, see my new post for tips on cutting pressed wood square with a round saw and my compressed wood cutting table plans that can be utilized with this compressed wood cutting maneuver.
Best way to rip plywood with circular saw tips:
Cut compressed wood sheets on the floor with proper support
That way, you’re certain to get strong, stable help so the pressed wood won’t move, regardless of whether you need to hop on top of it to finish your cut. It additionally guarantees that the cut-off piece won’t fragment, dampen or tumble off as you finish the cut. Lay 2x4s under the compressed wood opposite to the course of the cut. The 2x4s will be forfeited a tad when the sharp edge disregards them. However, that won’t influence the nature of the cut. The framework functions admirably for both tear cuts (corresponding to the grain) and crosscuts (opposite to the grain). The steadier the pressed wood, the better your odds for a completely smooth cut.
Set the cutting-edge profundity to simply clear the pressed wood thickness
Change the profundity of your edge with the goal that closes to a large portion of a carbide tooth that falls beneath the lower part of the pressed wood (photograph). That may appear to be superfluously particular, yet edge profundity has a serious effect in accomplishing smooth outcomes. This setting allows the teeth to shear the wood fiber instead of slash it, and it settles the edge (less vibration). The two elements limit saw bite marks. The more profound you set your saw edge, the more checks you get. Set the saw along the compressed wood edge, lift the gatekeeper and look carefully as you set the profundity. It’s additionally a decent and ideal opportunity to check the edge for chipped or missing teeth. An edge with terrible teeth or wood pitch development won’t cut neatly. Additionally, note that a roundabout saw cuts on the upstroke, which regularly fragments the top edge (facade) marginally. The base edge normally remains without a splinter. So consistently cut compressed wood with the great side down.
Clip-on a strong straightedge for a guide
You can purchase straightedges at home focuses and home improvement shops; however, for long cuts, I quite often utilize the “industrial facility cut” edge on a piece of 3/4-in—compressed wood. For a certain something, the manufacturing plant edge is typically entirely straight (sight along the edge to ensure) what’s more, the 3/4-in. Thick compressed wood will lie level, and it’ll remain unbending in the event that you pick a piece that is at any rate 12 in. wide. You just need to clip the finishes.
Test the guide for precision prior to making the cut
Here’s the place where you calibrate the cut. Draw a fine pencil line around 2 in. long, denoting the ideal width of your piece. Then beginning the saw, push the base plate against the guide, and simply scratch the pressed wood. Be certain the cutting edge is turning before you contact the pressed wood; else, you’ll splinter the edge. At that point, measure to the edge of the scratch to twofold check your estimations. On the off chance that you need to change the guide somewhat, make a point to change it at the two closures to guarantee a straight cut. Be particular here. Retest until the guide is situated perfectly.
Conclusion
In the end, following these tips will enable you to get more precise and clean cuts. Having the proper equipment and understanding of it is also a contributing factor. You can work on DIY projects around the house. That helps in getting a steadier hand and a better understanding. Keeping in practice makes it easier to spot ways to make it simpler and find more tricks to polish your skills. However, even if you’re an occasional worker, you can refer to tips as such and get going. This has been the best way to rip plywood with a circular saw.
